"Aaron Vick Starnes" (aaronstarnes)
01/13/2014 at 16:58 • Filed to: None | 4 | 7 |
The rocker panels on both sides of my old Ford were rotted waaay beyond repair. They looked more like Swiss cheese than American steel. So what did I do? I Cut 'em off!
I started with the passenger side because it seemed to be the worst of the two and it was tearing up everyone's legs as they climbed in and out of the car. I was pretty nervous about cutting into it. It's a big project and I had never done a rocker replacement before. I mean what if I cut it all up and couldn't get it back together?
I'd have a big rusty, un-driveable mess on my hands. But after loads of research on the internet, including my first foray into !!!error: Indecipherable SUB-paragraph formatting!!! to assemble my reference pictures, I had a good idea of what to do and felt like I could handle it... probably. To begin I broke out the saws-all and the cutting wheel.
The smell of hot steel hung thick in the air of the garage and the further I cut into the project the more I realized what a rusty old hulk I've been driving around. Digging into the rockers revealed a lot of rust issues that I figured were there but until this point I had seen face to face.
I the cut inner rockers along the bottom of the floor pans at the pinch welds to liberate both the inner and outer rockers at the same time. I cut the rocker off at the door pillar. I will need to remove the fender to get to the front portion of the rocker. I will get this done in part 2.
Taking the fender off will more than likely open up a brand new shiny can of worms to give me all kinds of fresh hell, but It's gotta get done, and doing it will give me even more to write about here. I have a nagging feeling that the grill is coming off to strip off the over-spray (thank you previous owner) and generally spruce things up.
Here both the inner and the outer rocker have been separated from the car. After cutting them off I went back with the cut-off wheel on my grinder and made sure that the bottom of the floor pan was totally flush. This is important because if the underside of the floor is uneven it won't fit flush against the new inner rocker.
I haven't pulled the fender off yet or purchased the new outer rocker panel. I do however have fresh inner rockers for both sides of the car. After I cut out all the old rotten steel I cleaned all the surfaces that I was going to weld to with a flap disc and then treated it all with weld through primer.
Weld through primer is a product that contains conductive elements that is applied to an area before weld and leaves a corrosion-resistant coating that can be welded on directly. It makes for cleaner welds while protecting against rust.
I don't know where the previous owner purchased these inner rocker panels from, but they aren't like any others that I've seen available for this car.
They were too long so I cut one of them down to fit and then tack welded it in position. I will finish welding them when I receive my new outer rocker panels and I can make sure everything lines up. I intend on trying my hand a fabricating some outer rocker panels for behind the door.
I have to say it's a nice feeling to see some fresh steel in the old Ford. Feels like I'm winning the battle against rust at least a little bit. For my next entry I'll pull of the front fender and try fitting my new outer rocker panel.
Stay tuned to see if I can manage to weld this mess back together into something that looks like a car, or if I will burn down my Ford and my mom's garage in the process.
Dunnik
> Aaron Vick Starnes
01/13/2014 at 17:09 | 0 |
When you consider that this is 65 years of rust we're looking at, that's not too bad.
I wish I had a garage and the skills/tools to weld. That you do earns you +10 Oppo points.
cluelessk
> Aaron Vick Starnes
01/13/2014 at 17:21 | 0 |
Make sure you you use some sort of anti corrosion product on the inside of the rockers or all your work will be for nothing. Even with weld through primers.
Aaron Vick Starnes
> Dunnik
01/13/2014 at 17:22 | 0 |
Thanks for the points. I'll try not to spend them all in one place. After high school I took some auto-body courses at a local community college. It was a blast and I learned a lot. You could too.
Aaron Vick Starnes
> cluelessk
01/13/2014 at 17:28 | 1 |
You bet. They will be primed and painted.
cluelessk
> Aaron Vick Starnes
01/13/2014 at 17:35 | 0 |
How you gonna paint the inside of the rockers?
You need something like this. http://3mcollision.com/3m-rust-fighte…
They make spray guns with hoses that spray a 360 degree pattern to run through small holes and cover all parts of inner panels.
Aaron Vick Starnes
> cluelessk
01/13/2014 at 17:39 | 1 |
My intention was to paint the insides before assembly. Then touch up any places that may have burned off.
cluelessk
> Aaron Vick Starnes
01/13/2014 at 17:56 | 0 |
That might work but I'd be scared of fire. Paint burns real easy. Just make sure you have a partner with a air gun ready to blow out each flame when it pops.
Looks like a fun project and best of luck. Takes guts to start chopping up a car.